發布時間：2018-06-27 03:54

  本文選題：三維機織 + 細觀模型�。� 參考：《南京航空航天大學》2017年碩士論文

【摘要】：本文所研究的三維斜交機織復合材料是一種新型的三維機織復合材料,它不但具有傳統三維機織復合材料所共有的優點,還具有傳統三維機織復合材料所沒有的獨特優勢,值得深入研究。本文主要對以下幾個方面進行了研究。首先,研究三維斜交機織預制件的機織工藝和紗線的空間走向,獲得了其紗線在空間的分布情況,直觀地展現了三維斜交機織復合材料的細觀結構。根據三維斜交機織復合材料的細觀結構和機織參數,建立了三維斜交機織復合材料的單胞模型。其次,采用成熟的樹脂傳遞模塑工藝對三維斜交機織復合材料進行復合成型,獲得了符合實驗要求試驗件;在MTS疲勞試驗機上完成三維斜交機織復合材料的拉伸性能測試,得到三維斜交機織復合材料的楊氏模量和泊松比。接著,采用剛度平均法證明三維斜交機織復合材料是一種正交各向異性材料,并用該方法以及Kregers加權平均模型分別求解其剛度性能,得到了獨立的9個工程彈性常數,并將理論預測的結果與實驗結果對比。最后,基于前述的單胞模型,用有限元分析計算得到了三維斜交機織復合材料的彈性常數并與實驗值對比;利用Abaqus/Explicit進行顯式動態分析,通過用戶自定義材料VUMAT子程序,對損傷單元進行剛度折減。分別采用Mises準則和Puck準則判斷基體和纖維材料的失效狀態,模擬拉伸作用下的損傷過程,最終得到了三維斜交機織復合材料的強度性能。
[Abstract]:The three-dimensional skew woven composite material studied in this paper is a new type of three-dimensional woven composite. It not only has the common advantages of the traditional 3D woven composite material, but also has the unique advantages of the traditional 3D woven composite material, which is worthy of further study. The main purpose of this paper is to study the following aspects. The weaving process of three-dimensional skew woven preform and the spatial direction of yarn are investigated. The distribution of yarn in space is obtained, and the microstructure of the three-dimensional skew woven composite material is displayed intuitively. A single cell model of 3D skew woven composites is built on the basis of the microstructure and weaving parameters of the 3D skew woven composite fabric. Secondly, the mature resin transfer molding process was used to compounded the three-dimensional skew woven composites, and the test parts were obtained. The tensile properties of the 3D skew woven composites were tested on the MTS fatigue test machine, and the young's modulus and Poisson's ratio of the 3D skew woven composites were obtained. The degree averaging method proves that the three-dimensional skew woven composite material is a kind of orthotropic material, and uses this method and the Kregers weighted average model to solve its stiffness performance respectively. The independent 9 engineering elastic constants are obtained, and the results from the theoretical prediction are compared with the experimental results. The elastic constants of the three-dimensional skew woven composites were calculated and compared with the experimental values. The explicit dynamic analysis was carried out by Abaqus/Explicit. The stiffness reduction of the damage unit was reduced by the user custom material VUMAT subroutine. The failure state of the base body and fiber material was judged by the Mises criterion and the Puck criterion respectively. Finally, the strength properties of 3D skew woven composites were obtained by using the damage process.
【學位授予單位】：南京航空航天大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TB33

【參考文獻】

相關期刊論文 前7條

1 鐘翔嶼;紡織復合材料在航空航天工業上的應用[J];紡織導報;2003年06期

2 吳德隆,沈懷榮;紡織結構復合材料的力學性能研究[J];力學進展;2001年04期

3 易洪雷,丁辛;三維機織復合材料力學性能研究進展[J];力學進展;2001年02期

4 楊連賀,邱冠雄,黃故;任意結構三維機織復合材料彈性性能的計算機模擬[J];復合材料學報;2000年02期

5 黃故,馬崇啟,林國財,吳曉青,吳濤;三維機織復合材料的研制[J];紡織學報;1999年01期

6 丁辛,易洪雷;正交接結組織結構特征及其對纖維體積含量的影響[J];天津紡織工學院學報;1998年04期

7 易洪雷,丁辛;多層機織物增強復合材料的拉伸與剪切性能研究[J];玻璃鋼/復合材料;1997年02期

相關會議論文 前2條

1 丁辛;易洪雷;;論多層機織物接結組織結構的表征[A];第十二屆玻璃鋼/復合材料學術年會論文集[C];1997年

2 李嘉祿;;三維編織復合材料的研究和應用[A];復合材料：生命、環境與高技術——第十二屆全國復合材料學術會議論文集[C];2002年

，

本文編號：2072564