發布時間：2018-08-16 12:47

【摘要】：近年來,利用印刷電子技術制備半導體器件和導電線路越來越受到人們重視,而噴墨打印技術作為印刷電子技術中的重要組成部分受到廣泛關注。本文主要工作包括自主制備出性能穩定,形貌統一的納米銀顆粒,并將其配置成可噴墨打印導電油墨;進行單層和多層導電線路打印實驗,研究和優化實驗條件及打印機參數設置,得到打印銀(Ag)線最佳性能。(1)分別制備出兩種不同保護劑的納米銀顆粒,并對產物進行表征,測得保護劑為聚丙烯酸的納米銀粒徑約20 nm,保護劑為十二胺的納米銀粒徑約50 nm;由于聚丙烯酸屬于水溶性材料,在銀顆粒表面屬于弱吸附容易去除,因此選擇聚丙烯酸做保護劑制備的納米顆粒制備導電油墨,添加相關助劑以改善噴墨性能;(2)同時,選擇環氧樹脂板、相片紙、聚對苯二甲酸乙二醇酯等做基底進行打印實驗,并對基底進行表面改性,提高打印線路附著性和導電圖案分辨率。單獨分析環氧樹脂板做基底的打印成膜性及克服咖啡環效應的實驗條件,并對導電機理進行研究,探討燒結溫度、打印層數、燒結時間與樣品電阻率的關系。以相片紙做基底,110℃條件下燒結1 h,可獲得電阻率為8μΩ·cm的導線;(3)最后將旋涂技術與噴墨打印技術相結合,以聚對苯二甲酸乙二醇酯做基底,聚甲基丙烯酸甲酯作絕緣層,進行多層電路制備實驗的探索,為該課題下一步研究提供參考。
[Abstract]:In recent years, more and more attention has been paid to the preparation of semiconductor devices and conductive circuits by printing electronics technology. Inkjet printing technology, as an important part of printing electronics technology, has attracted wide attention. Printing conductive ink; single-layer and multi-layer conductive circuit printing experiments, research and optimize the experimental conditions and printer parameters settings, get the best performance of printed silver (Ag) line. (1) Two kinds of nano-silver particles with different protective agents were prepared, and the products were characterized. The particle size of nano-silver with polyacrylic acid was about 20 nm, and the protective agent was determined. The particle size of nano-silver dodecylamine is about 50 nm; because polyacrylic acid is a water-soluble material, it is easy to be removed by weak adsorption on the surface of silver particles, polyacrylic acid is chosen as a protective agent to prepare conductive ink, and relevant additives are added to improve the ink-jet performance; (2) At the same time, epoxy resin board, photo paper and poly (terephthalic acid) are selected. Ethylene glycol ester was used as the substrate for printing experiment, and the substrate was modified to improve the adhesion of printing circuit and the resolution of conductive pattern. The relationship between the resistivity and the sample resistivity is studied. The 8_ cm resistivity can be obtained by sintering the photo paper at 110 C for 1 h. (3) Finally, the spin-coating technology is combined with the inkjet printing technology, and the experiment of multi-layer circuit preparation using polyethylene terephthalate as the substrate and polymethyl methacrylate as the insulating layer is explored. The next step is to provide reference.
【學位授予單位】：南京郵電大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TB383.1;TP334.83

【參考文獻】

相關碩士學位論文 前1條

1 吳美蘭;高分散穩定性納米銀顆粒的合成與性能研究[D];天津大學;2012年

，

本文編號：2186027