基于DSP的MODEM傳輸系統硬件PCB設計及信號完整性分析
發布時間：2018-12-17 10:00
【摘要】：短波通信是指利用波長為10～100米的無線電波進行數據傳輸的一種遠距離通信方式。由于短波通信系統設備成本低,體積小,抗干擾能力強的特性,使短波通信廣泛應用于軍事,海事,氣象等領域。 隨著微電子技術,軟件無線電技術的發展,作為短波通信設備的核心部分,調制解調器向小型化,數字化,高速,高可靠有效性的方向發展。 本文在第三代通信協議MIL_STD_188_110C的基礎上,提出了高速串行調制解調器全新的硬件平臺架構：雙核高性能DSP+FPGA。同時通過EDA電路仿真軟件設計硬件平臺高速電路,完成信號完整性分析。其主要工作如下。 1.基于對高速電路信號完整性理論的研究,介紹了常見的信號完整性問題,給出了解決信號完整性問題的措施,為設計高速電路提供理論依據。 2.統籌設計規劃硬件平臺,將硬件平臺分為DSP,FPGA和音頻信號處理三個模塊,并圍繞三個模塊核心器件DSP,FPGA和音頻芯片的功耗,時鐘,以及外圍接口要求實現外圍電路的設計。根據系統功耗,上電時序等設計硬件平臺的電源網絡。 3.系統高速PCB設計,分析系統高速信號線的信號完整性,并通過仿真軟件SigXplorer和Hyperlynx對高速信號線進行仿真,給出仿真結果和改善信號質量的方法。
[Abstract]:Short-wave communication is a kind of long-distance communication which uses radio waves of 10 ~ 100 meters. Shortwave communication system is widely used in military, maritime and meteorological fields because of its low cost, small volume and strong anti-jamming ability. With the development of microelectronic technology and software radio technology, as the core part of shortwave communication equipment, modem is developing towards miniaturization, digitalization, high speed, high reliability and efficiency. Based on the third generation communication protocol MIL_STD_188_110C, this paper proposes a new hardware platform architecture of high speed serial modem: dual core high performance DSP FPGA.. At the same time, the high-speed circuit of hardware platform is designed by EDA circuit simulation software, and the signal integrity analysis is completed. Its main work is as follows. 1. Based on the research on the theory of signal integrity in high-speed circuits, the common problems of signal integrity are introduced, and the measures to solve the problems are given, which provide the theoretical basis for the design of high-speed circuits. 2. The hardware platform is designed as a whole. The hardware platform is divided into three modules: DSP,FPGA and audio signal processing. The design of peripheral circuit is realized around the power consumption, clock and peripheral interface of DSP,FPGA and audio chip. According to the system power consumption, power sequence and other design hardware platform power supply network. 3. The high speed PCB of the system is designed to analyze the signal integrity of the high speed signal line of the system. The simulation results and the methods to improve the signal quality are given through the simulation software SigXplorer and Hyperlynx.
【學位授予單位】：北京郵電大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TN41;TN911.6
本文編號：2384049
[Abstract]:Short-wave communication is a kind of long-distance communication which uses radio waves of 10 ~ 100 meters. Shortwave communication system is widely used in military, maritime and meteorological fields because of its low cost, small volume and strong anti-jamming ability. With the development of microelectronic technology and software radio technology, as the core part of shortwave communication equipment, modem is developing towards miniaturization, digitalization, high speed, high reliability and efficiency. Based on the third generation communication protocol MIL_STD_188_110C, this paper proposes a new hardware platform architecture of high speed serial modem: dual core high performance DSP FPGA.. At the same time, the high-speed circuit of hardware platform is designed by EDA circuit simulation software, and the signal integrity analysis is completed. Its main work is as follows. 1. Based on the research on the theory of signal integrity in high-speed circuits, the common problems of signal integrity are introduced, and the measures to solve the problems are given, which provide the theoretical basis for the design of high-speed circuits. 2. The hardware platform is designed as a whole. The hardware platform is divided into three modules: DSP,FPGA and audio signal processing. The design of peripheral circuit is realized around the power consumption, clock and peripheral interface of DSP,FPGA and audio chip. According to the system power consumption, power sequence and other design hardware platform power supply network. 3. The high speed PCB of the system is designed to analyze the signal integrity of the high speed signal line of the system. The simulation results and the methods to improve the signal quality are given through the simulation software SigXplorer and Hyperlynx.
【學位授予單位】：北京郵電大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TN41;TN911.6
【參考文獻】
相關期刊論文 前6條
1 韓少華 ,陳健 ,傅豐林;多路音頻模擬接口芯片TLV320AIC10與DSP串行通信的設計與實現[J];電子產品世界;2002年18期
2 蔡湘平;;電源驅動芯片UCD9222的數字電源設計[J];單片機與嵌入式系統應用;2013年01期
3 宋建民;;短波數據調制解調器的現狀與發展[J];電子工程師;1997年01期
4 沈越泓;沈振元;;短波高速調制解調器發展新動向[J];軍事通信技術;1988年02期
5 董彬虹;李少謙;;短波通信的現狀及發展趨勢[J];信息與電子工程;2007年01期
6 樊延虎;短波高速調制解調器的設計[J];延安大學學報(自然科學版);2002年03期
，本文編號：2384049
本文鏈接：http://www.wukwdryxk.cn/kejilunwen/dianzigongchenglunwen/2384049.html
