發布時間：2018-08-13 18:53

【摘要】：輸送帶是帶式輸送機的重要部件,輸送帶的成本占整個輸送機設備投資的1/3以上。輸送帶在整個輸送過程中要產生彎曲變形,如凸弧段、凹弧段、過渡段和翻轉段等,其中以過渡段和翻轉段產生的變形更為劇烈,輸送帶的變形使輸送帶在寬度方向的張力重新分布,很容易產生輸送帶邊緣的撕裂和輸送帶中部褶皺。對輸送帶過渡段和翻轉段進行分析,得到輸送帶在寬度方向張力的分布情況,進而為輸送帶接頭的設計研究提供一定的理論參考。得到輸送帶在過渡段和翻轉段的具體受力情況,對合理選擇輸送帶,降低輸送帶安全系數,進而降低輸送機的成本,減少能源消耗具有重要意義。 利用有限元軟件ANSYS建立了鋼絲繩芯輸送帶的有限元模型,橡膠選擇2參數的Mooney-Rivlin模型,該模型在伸長量小于100%時能準確模擬橡膠材料,鋼絲繩選用SOLID185單元。通過定義和設置接觸的控制節點,實現剛性面(托輥)的轉動,定義和控制MPC184單元,實現輸送帶的翻轉。最終實現了輸送帶在過渡段的槽形變形和翻轉段的翻轉變形。所得分析結果與實際情況有十分良好的吻合性,誤差也在允許的范圍內。 采用有限元的方法對過渡段輸送帶進行分析,得到了過渡段輸送帶在寬度方向的張力分布情況。輸送帶張力在過渡段呈槽形分布,輸送帶張力在兩側托輥上呈微凹形分布,在中間托輥上呈微凸弧分布,分別在中間托輥兩端出輸送帶張力取得最小值,在輸送帶邊緣鋼絲繩出取得最大張力值。 對翻轉段輸送帶進行的有限元分析,得到了翻轉段輸送帶在寬度方向的張力分布情況。送帶在翻轉段的張力分布為斜凹形拋物線分布,在輸送帶下邊緣鋼絲繩出取得張力最大值(大值),在輸送帶上邊緣取得張力最大值(小值),在靠近輸送帶中間上邊緣出取得最小值。
[Abstract]:Conveyor belt is an important part of belt conveyor, the cost of conveyor belt accounts for more than a third of the total equipment investment. The conveyor belt has to produce bending deformation in the whole transportation process, such as convex arc, concave arc, transition section and flip section, among which the deformation produced by the transition section and the flip section is more severe. The deformation of conveyor belt redistributes the tension of conveyor belt in width direction, and it is easy to produce the tear of the belt edge and the fold in the middle of the belt. The distribution of the belt tension in the width direction is obtained by analyzing the transition section and the flip section of the conveyor belt, which provides a certain theoretical reference for the design and research of the conveyor belt joint. It is of great significance to select the conveyor belt reasonably, reduce the safety coefficient of the conveyor belt, and then reduce the cost and energy consumption of the conveyor. The finite element model of steel wire core conveyor belt is established by using finite element software ANSYS, and the Mooney-Rivlin model with 2 parameters is selected by rubber. The model can accurately simulate rubber material when the elongation is less than 100, and SOLID185 element is used for wire rope. By defining and setting the contact control node, the rotation of rigid surface (roller) is realized, and the MPC184 unit is defined and controlled, and the conveyor belt is flipped. Finally, the groove deformation and the flip deformation of the conveyor belt in the transition section are realized. The results are in good agreement with the actual situation, and the error is within the allowable range. The finite element method is used to analyze the conveyor belt of the transition section, and the distribution of the tension in the width direction of the belt is obtained. The tension of the conveyor belt is distributed in the transition section, the tension of the belt is microconcave on the two sides of the roller, the tension of the belt is distributed in the arc on the middle roller, and the tension of the conveyor belt is obtained at the two ends of the intermediate roller to obtain the minimum value. The maximum tension value is obtained at the edge of the conveyor belt wire rope. Based on the finite element analysis, the tension distribution in the width direction of the inverted belt is obtained. The tension distribution of the belt in the flip section is an oblique concave parabola distribution. The maximum tension (large value) is obtained at the edge of the conveyor belt, the maximum tension (small value) is obtained at the upper edge of the conveyor belt, and the minimum value is obtained near the upper edge of the conveyor belt.
【學位授予單位】：東北大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TH222

【參考文獻】

相關期刊論文 前10條

1 程哲;張正藝;宋楊;解德;;橡膠材料超彈性本構模型的簡化標定方法[J];固體力學學報;2010年S1期

2 吳曉宇,吳清文,楊洪波,何惠陽;對有限元分析結果判定方法的探討[J];機械設計與研究;2003年06期

3 杜平安;有限元網格劃分的基本原則[J];機械設計與制造;2000年01期

4 蘇春;關于安全系數法和可靠性設計的討論[J];機械科學與技術;1997年01期

5 左亮;肖緋雄;;橡膠Mooney-Rivlin模型材料系數的一種確定方法[J];機械制造;2008年07期

6 楊達文;高強度輸送帶的強度校核[J];煤礦機械;2000年12期

7 張?jiān)��?;基于有限元的輸送帶模態分析[J];煤礦機械;2012年02期

8 黃志超,包忠詡,周天瑞,陳澤中;有限元網格劃分技術研究[J];南昌大學學報(工科版);2001年04期

9 侯開璽,李付林;膠帶輸送機凸弧段的結構設計[J];煤礦機械;1996年06期

10 鄭明軍,王文靜,陳政南,吳利軍;橡膠Mooney-Rivlin模型力學性能常數的確定[J];橡膠工業;2003年08期

，

本文編號：2181872