發布時間：2018-11-27 13:41

【摘要】：在清香型白酒的釀制過程中,酒曲非常重要;制曲機作為酒曲制作的關鍵裝備,重要性不言而喻。機械化制曲具有很多人工制曲無法比擬的優點如勞動生產率高、制曲車間條件好和生產成本低等。但是機械制曲也存在設備維修率高、水資源浪費嚴重和液壓回路的壓力脈動過大等缺陷,這些缺陷阻礙了各大白酒企業自動化制曲機的應用。因此,本課題首先對汾酒集團制曲車間大曲的生產流程做了詳細的研究,綜合研究國內外曲胚塊生產設備,參與設計一套穩定、高效、節水的清香型酒曲制曲機,來滿足市場的緊迫需求。本文首先根據制曲機存在缺陷,對制曲機的結構進行設計,然后設計伺服液壓回路,對蓄能器吸收脈動回路系統和伺服閥控液壓缸系統建立了數學模型,并推出了清香型酒曲制曲機在正常工作時,蓄能器壓力脈動傳遞函數和伺服閥控制液壓缸的傳遞函數,應用MATLAB/Simulink軟件繪制出在單位階躍信號下的響應曲線,并對液壓缸系統的模型進行了分析,系統無超調、穩定性好,但是響應速度達不到設計要求,故在系統中引入PID來對其改進,以保證設備的關鍵參數能達到生產工藝要求。為了防止制曲機的踩壓系統和機架在激振頻率下發生共振,本文通過ABAQUS軟件確定踩壓系統、機架的固有頻率和模態柔度,確保制曲機在合理的頻率范圍內工作。為了檢驗建模和校正結果的正確性,在ADAMS和AMESim軟件中搭建聯合仿真平臺,并進行仿真,仿真結果表明引入PID控制器和蓄能器對改善液壓系統具有顯著意義。為了進一步檢驗設計的設備在現場的穩定性,在現場搭建實驗平臺,進行了應用測試,通過Hydrotechnik Multi-System 5060液壓萬用表對液壓系統的壓力流量進行了檢測;使用TYPE6230噪聲檢測儀對現場噪聲進行檢測;通過速度和位移傳感器對液壓缸的速度和位移進行了檢測。根據檢測結果與仿真結果的對比,可知清香型酒曲制曲機的設計合理,完全能滿足現場工藝要求。
[Abstract]:Liquor is very important in the brewing process of Fen-Flavor Liquor, and its importance is self-evident as the key equipment of Liquor making. Mechanized koji making has many advantages, such as high labor productivity, good working conditions and low production cost. However, mechanical koji has some defects such as high maintenance rate of equipment, serious waste of water resources and excessive pressure pulsation of hydraulic circuit. These defects hinder the application of automatic koji making machines in major liquor enterprises. Therefore, this subject first made a detailed study on the production process of Daqu in Fenjiu Group koji making workshop, comprehensively studied the domestic and foreign koji production equipment, and participated in the design of a stable, efficient, water-saving wine koji making machine. To meet the urgent needs of the market. In this paper, the structure of the machine is designed according to the defects of the machine, and then the servo hydraulic circuit is designed. The mathematical model of the accumulator absorption pulsation loop system and the servo valve controlled hydraulic cylinder system is established. The pressure pulsation transfer function of accumulator and the transfer function of servo valve control hydraulic cylinder are deduced when the wine koji machine works normally, and the response curve under the unit step signal is drawn by using MATLAB/Simulink software, and the pressure pulsation transfer function of the accumulator and the transfer function of the servo valve control hydraulic cylinder are obtained. The model of the hydraulic cylinder system is analyzed. The system has no overshoot and good stability, but the response speed is not up to the design requirement. Therefore, PID is introduced into the system to improve the system to ensure that the key parameters of the equipment can meet the requirements of the production process. In order to prevent the pressure system and the frame of the starter from resonance under the exciting frequency, the paper determines the natural frequency and modal flexibility of the trampling system and the frame by ABAQUS software, so as to ensure that the machine works within a reasonable frequency range. In order to verify the correctness of the modeling and correction results a joint simulation platform was built in ADAMS and AMESim software. The simulation results show that the introduction of PID controller and accumulator is significant to improve the hydraulic system. In order to further test the stability of the designed equipment in the field, an experimental platform was set up, and the application test was carried out. The pressure and flow of the hydraulic system were tested by Hydrotechnik Multi-System 5060 hydraulic multimeter. The TYPE6230 noise detector is used to detect the field noise, and the speed and displacement of the hydraulic cylinder are measured by speed and displacement sensors. According to the comparison between the test results and the simulation results, it can be seen that the design of the wine-making machine is reasonable and can completely meet the requirements of the field technology.
【學位授予單位】：太原理工大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TS261.3

【參考文獻】

相關期刊論文 前10條

1 王瑛;付捷;羅鋼;;酒廠轉盤式多工位曲塊壓制機的設計[J];包裝與食品機械;2016年06期

2 衛進;邵良鋒;秦禹;黃鎮;;圓盤回轉式壓塊機液壓系統設計與仿真[J];機床與液壓;2016年16期

3 衛進;秦禹;邵良鋒;;凸輪分割式旋轉踩曲機傳動系統的研究與仿真[J];食品與機械;2015年03期

4 秦禹;衛進;;基于MATLAB與Pro/E弧面凸輪的設計方法[J];煤礦機械;2015年05期

5 王慧;康環宇;孟冉;;模糊PID在冷軋機厚度控制系統上的應用[J];測控技術;2014年06期

6 衛進;常濤柱;楊濤;;基于AMESim多工位回轉工作臺液壓系統仿真研究[J];液壓與氣動;2014年04期

7 上官紅喜;;液壓驅動面條擠壓機的設計[J];食品與機械;2014年01期

8 陳惠卿;;工程機械用液壓油的選擇[J];液壓氣動與密封;2012年12期

9 劉堅;林汲;雷振河;呂利華;趙良啟;;汾酒酒醅有機酸的研究及釀造工藝的優化[J];食品與發酵工業;2012年01期

10 馬凱;崔哲男;鄭曉衛;韓建書;杜小威;陳晶瑜;韓北忠;;汾酒大曲可培養真菌多樣性的初步分析[J];中國釀造;2011年08期

相關碩士學位論文 前1條

1 張靜;多點采壓壓曲機設計及其關鍵結構件仿真研究[D];太原理工大學;2009年

，

本文編號：2360976