大型船舶錨唇智能設計與數字化驗證技術研究
發布時間：2018-08-27 19:21
【摘要】：錨唇，作為錨系的一個部件，其表面形態為復雜曲面，而曲面的復雜形態主要歸咎于它要滿足于一定的運動性能要求。以往錨唇都是通過設計者豐富的經驗并配合大量的木模拉錨試驗進行曲面設計，這種設計方法不僅費時、費力，還會造成材料的浪費。本文通過對國內外曲面設計技術進行分析，提出一種新的錨唇曲面設計方法。這一方法是基于CATIA二次開發技術，利用共軛包絡理論求解出錨桿、錨爪與錨唇接觸處的曲面，并利用MATLAB繪圖功能繪制出其接觸曲面的形狀以及獲取其曲面上的型值點。以這些型值點為基礎，對錨唇曲面進行智能設計。 其次，錨系運動為多剛體接觸運動，為了給錨系建立較為合理的動力學模型以便進行正確的拉錨仿真分析，對接觸碰撞動力學的知識進行了系統闡述，介紹了ADAMS中接觸碰撞力學模型以及接觸碰撞判斷規則，并利用ADAMS仿真功能分析了錨系運功過程中的主要影響因素，以便于后期的仿真驗證。 最后，以10000TEU標箱集裝箱船的錨唇為例，利用提出的新的錨唇設計方法對其進行設計。設計完成之后，利用UG的仿真功能對其錨系進行運動仿真分析，驗證設計的錨唇是否合理，能否達到設計者的要求。 總之，本文將船舶錨唇設計作為研究方向，并以求解錨桿、錨爪與錨唇曲面接觸處的曲面和其曲面上型值點為主要的研究對象進行了具體的闡述，，對實現船舶錨唇智能設計具有一定的參考意義。
[Abstract]:Anchor lip, as a part of anchorage system, its surface shape is complex curved surface, and the complex shape of curved surface is mainly attributed to its motion performance requirements. In the past, anchor lip was designed by the designer's rich experience and cooperated with a large number of wooden model pull anchor test. This design method is not only time-consuming, laborious, but also constructed. This paper presents a new design method of anchor lip surface based on the analysis of surface design technology at home and abroad. This method is based on CATIA secondary development technology, using conjugate envelope theory to solve the surface of the contact between anchor rod, anchor claw and anchor lip, and using MATLAB drawing function to draw the shape of its contact surface. Based on these values, intelligent design of anchor lip surfaces is carried out.
Secondly, the motion of anchorage system is a multi-rigid-body contact motion. In order to establish a more reasonable dynamic model for anchorage system in order to carry out the correct simulation analysis of pulling anchor, the knowledge of contact collision dynamics is systematically expounded. The mechanical model of contact collision and the judgment rules of contact collision in ADAMS are introduced, and the simulation function of ADAMS is used to analyze it. The main influencing factors in the work of anchor system are convenient for later simulation.
Finally, taking the anchor lip of 10 000 TEU container ship as an example, the new design method of anchor lip is used to design the ship. After the design is completed, the motion simulation of the anchor system is carried out by using UG simulation function to verify whether the designed anchor lip is reasonable and can meet the requirements of the designer.
In a word, this paper takes the design of ship's anchor lip as the research direction, and takes the solution of anchor rod, the curved surface of the contact between anchor claw and anchor lip surface and the value points on the curved surface as the main research objects. It has a certain reference significance to realize the intelligent design of ship's anchor lip.
【學位授予單位】：江蘇科技大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U664.42
本文編號：2208203
[Abstract]:Anchor lip, as a part of anchorage system, its surface shape is complex curved surface, and the complex shape of curved surface is mainly attributed to its motion performance requirements. In the past, anchor lip was designed by the designer's rich experience and cooperated with a large number of wooden model pull anchor test. This design method is not only time-consuming, laborious, but also constructed. This paper presents a new design method of anchor lip surface based on the analysis of surface design technology at home and abroad. This method is based on CATIA secondary development technology, using conjugate envelope theory to solve the surface of the contact between anchor rod, anchor claw and anchor lip, and using MATLAB drawing function to draw the shape of its contact surface. Based on these values, intelligent design of anchor lip surfaces is carried out.
Secondly, the motion of anchorage system is a multi-rigid-body contact motion. In order to establish a more reasonable dynamic model for anchorage system in order to carry out the correct simulation analysis of pulling anchor, the knowledge of contact collision dynamics is systematically expounded. The mechanical model of contact collision and the judgment rules of contact collision in ADAMS are introduced, and the simulation function of ADAMS is used to analyze it. The main influencing factors in the work of anchor system are convenient for later simulation.
Finally, taking the anchor lip of 10 000 TEU container ship as an example, the new design method of anchor lip is used to design the ship. After the design is completed, the motion simulation of the anchor system is carried out by using UG simulation function to verify whether the designed anchor lip is reasonable and can meet the requirements of the designer.
In a word, this paper takes the design of ship's anchor lip as the research direction, and takes the solution of anchor rod, the curved surface of the contact between anchor claw and anchor lip surface and the value points on the curved surface as the main research objects. It has a certain reference significance to realize the intelligent design of ship's anchor lip.
【學位授予單位】：江蘇科技大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U664.42
【參考文獻】
相關期刊論文 前7條
1 姚珍祥;;錨鏈筒與拋起錨的關系[J];船舶工程;2007年01期
2 李純金;劉志強;王明強;邱小虎;;基于虛擬樣機技術的VLCC錨系運動仿真研究[J];船舶工程;2008年06期
3 舒根泉;船舶錨鏈筒布置設計[J];船舶設計通訊;2000年Z2期
4 于剛;;簡述錨系設計[J];船舶設計通訊;2010年S2期
5 袁紅莉;熊云峰;;運輸船舶錨鏈筒和錨臺的設計和放樣[J];江蘇船舶;2009年03期
6 王小平,葉正麟,孟雅琴,李紅達;基于伸縮因子的參數曲線自由變形[J];計算機輔助設計與圖形學學報;2002年01期
7 李宇鵬;孫洪勝;劉鳴華;趙永昌;張世珍;;轎車車身殼體曲面零件的仿生設計研究[J];制造技術與機床;2011年12期
本文編號：2208203
本文鏈接：http://www.wukwdryxk.cn/kejilunwen/chuanbolw/2208203.html
最近更新
教材專著
