發布時間：2018-03-29 11:35

  本文選題：鉭鎢合金　切入點：霍普金森壓桿　出處：《稀有金屬材料與工程》2017年10期

【摘要】：對2種鉭鎢合金(Ta-2.5W和Ta-10W,鎢的質量分?jǐn)?shù)分別為2.5%和10%)的準靜態和動態變形行為進行了系統研究。根據準靜態壓縮實驗、霍普金森壓桿(SHPB)實驗結果,表明2種鉭鎢合金的流動應力對加載應變率和鎢的含量較為敏感,并擬合得到了2種鉭鎢合金的JC本構模型參數。其次,為驗證本構模型的合理性,開展了泰勒撞擊實驗和數值模擬研究,應變率范圍為10~3~10~4 s~(-1),數值模擬得到的泰勒桿側輪廓與撞擊端面輪廓與實驗吻合較好。最后,為研究鉭鎢合金變形后的細觀特性,對桿件進行了光學顯微照片分析。本研究方法與結果可為材料本構關系的確定提供借鑒。
[Abstract]:The quasi-static and dynamic deformation behaviors of Ta-2.5W and Ta-10W of two kinds of tantalum tungsten alloys were systematically studied. The experimental results of Hopkinson compression bar SHPBwere based on the quasi-static compression experiment, and the mass fraction of tungsten was 2.5% and 10%, respectively. It is shown that the flow stress of the two tantalum-tungsten alloys is sensitive to the loading strain rate and the tungsten content, and the parameters of the JC constitutive model of the two kinds of tantalum tungsten alloys are fitted. Secondly, to verify the rationality of the constitutive model, Taylor impact experiments and numerical simulation studies have been carried out. The strain rate ranges from 10 ~ (3) ~ 10 ~ (10) ~ (4) s ~ (-1) ~ (-1). The profile of Taylor bar side and the profile of impact end surface obtained by numerical simulation are in good agreement with the experimental results. Finally, in order to study the mesoscopic characteristics of tantalum and tungsten alloy after deformation, The method and results of this study can be used for reference in determining the constitutive relationship of the material.
【作者單位】： 南京理工大學;南洋理工大學;中國兵器科學研究院寧波分院;
【基金】：the Zijin Intelligent Program,Nanjing University of Science and Technology(2013_ZJ_0101) Qing Lan Project of Jiangsu Province State Key Laboratory of Explosion Science and Technology(Beijing Institute of Technology)(KFJJ15-07M)
【分類號】：TG146.416

【相似文獻】

相關期刊論文 前2條

1 李學光;梁嵬;王大力;隋禮輝;陳莉丹;;鉭鎢合金球面圓盤旋壓仿真研究[J];制造業自動化;2014年07期

2 王珊;汪明樸;陳暢;夏福中;左波;張婉;;鉭及鉭鎢合金冷軋變形過程中的組織和性能[J];材料熱處理學報;2012年06期

相關會議論文 前2條

1 李大紅;;鉭鎢合金在10GPa沖擊加載下的層裂和損傷[A];中國工程物理研究院科技年報（1998）[C];1998年

2 李大紅;;Ta4W和Ta8W鉭鎢合金的動態破壞[A];中國工程物理研究院科技年報（1999）[C];1999年

相關碩士學位論文 前1條

1 金鵬;鉭鎢合金箔材組織結構及性能的研究[D];中南大學;2009年

，

本文編號：1680958