發布時間：2018-05-18 23:14

  本文選題：螺母 + 內螺紋檢測��； 參考：《合肥工業大學》2017年碩士論文

【摘要】：螺母作為機械設備主要連接零部件之一,依靠其優秀的機械特性,廣泛的應用于各類機械設備中。因此對螺母使用性能進行檢測顯得尤為重要。對目前螺紋檢測設備進行調查研究,發現存在檢測效率低、檢測成本高等問題,難以滿足螺母出口企業的批量全檢要求。因此有必要研制一臺適用性強、效率高、成本低的螺母內螺紋檢測設備。首先,根據選定的接觸式綜合測量法以及制定的設備技術指標,本文提出立式螺母內螺紋檢測機的總體設計方案,采用模塊化思想將設計方案分為機架總成、檢測平臺總成和螺母移動定位總成等,對各組成部分進行設計計算,驗證設計合理性。樣機完成后進行樣機實驗,對實驗數據進行分析總結。針對實驗過程中出現的問題提出解決方案,并對立式螺母內螺紋檢測機設計方案進行總結。然后,針對立式螺母內螺紋檢測機實驗后出現的問題,提出臥式螺母內螺紋檢測機的總體設計方案。采用模塊化思想將設計方案分為機架總成、移動總成、檢測平臺總成、上料總成和分揀總成等,并對主要零部件進行設計與選型計算。其中設計的雙向?qū)�桿式離合器通過與齒輪結構配合,實現一個伺服電機同時控制四個檢測工位。最后,為驗證設計方案的可靠性和安全性,對設備進行建模和虛擬裝配,并對重要的零件進行有限元分析。同時參與完成臥式螺母內螺紋檢測機控制系統的需求分析、方案設計、工作流程制定等工作。
[Abstract]:As one of the main parts of the mechanical equipment, nut is widely used in all kinds of mechanical equipment depending on its excellent mechanical properties. Therefore, it is very important to detect the performance of nuts. Investigation and Research on the current thread detection equipment have found that there is a low detection efficiency and high detection cost, and it is difficult to meet the nut. Therefore, it is necessary to develop a screw thread testing equipment with strong applicability, high efficiency and low cost. First, according to the selected contact comprehensive measurement method and the set of equipment technical indexes, the overall design scheme of the vertical nut internal thread testing machine is proposed in this paper, and the design of the modular idea will be adopted. The scheme is divided into the frame assembly, the detection platform assembly and the nut moving and positioning assembly. The design and calculation of the components are designed to verify the rationality of the design. After the prototype is completed, the prototype experiment is carried out and the experimental data are analyzed and summarized. The solutions are proposed for the problems in the experimental process, and the vertical nut inner thread testing machine is designed. The scheme is summarized. Then, in view of the problems of the vertical nut inner thread testing machine, the overall design scheme of the horizontal nut internal thread testing machine is proposed. The design scheme is divided into the frame assembly, the mobile assembly, the inspection platform assembly, the assembly and the sorting assembly, and the design and design of the main parts and components. The two-way guide rod clutch is designed to realize a servo motor and control four detection stations at the same time by cooperating with the gear structure. Finally, in order to verify the reliability and safety of the design scheme, the equipment is modeled and assembled, and the important parts are analyzed by finite element analysis. Meanwhile, the horizontal nut is completed. Requirements analysis, program design, workflow formulation of internal thread detecting machine control system.
【學位授予單位】：合肥工業大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TG85

【參考文獻】

相關期刊論文 前10條

1 景濤;馮武衛;;螺母自動上料及攻絲系統結構設計[J];機電工程;2016年11期

2 朱勝;李萍;井江;;一種滾柱式超越離合器的改進設計[J];現代制造技術與裝備;2016年06期

3 張義民;石晏霖;李常有;鄧強;;單螺母滾珠絲杠副靜剛度可靠性及靈敏度分析[J];哈爾濱工業大學學報;2016年07期

4 郝東治;趙杏根;;超越離合器在機床上的應用[J];紡織器材;2016年01期

5 韓軍;張玲聰;李明亞;;螺母副摩擦熱對高速空心滾珠絲杠熱特性影響分析[J];機械設計與制造;2015年12期

6 何亞銀;梁應選;楊明亮;;滾珠絲杠螺母內滾道位置度的測量[J];機械設計與研究;2015年04期

7 李曉丹;王曉磊;;活塞螺母防松專機系統設計[J];機床與液壓;2015年14期

8 侯東明;陳文冬;高興華;;內螺紋測量方法研究[J];裝備制造技術;2015年01期

9 沈燦鋼;;自動物料分揀裝置的設計與實現[J];數字技術與應用;2014年09期

10 李海龍;王恒斌;李林濤;王棟;;一種氣缸選型模擬計算方法[J];液壓氣動與密封;2014年09期

，

本文編號：1907635