發布時間：2018-07-30 08:49

【摘要】：傳統的船型優化一般基于靜水阻力最低，以靜水中的快速性來衡量船型的好壞。而實際上，一艘船舶在其營運的絕大多數時間內都是在不同海況下航行的，船舶會受到由于波浪引起的阻力增值，靜水中快速性好的船其波浪中的快速性不一定也是好的。此外，降低船舶的航行阻力、減少主機功率也是減小燃油消耗、降低碳排放的關鍵。本文以一艘30萬噸級的油船作為研究對象，以波浪中的總阻力最低作為目標函數，通過構建基于靜水阻力和波浪增阻的集成優化系統實現了船型的自動優化，得到了波浪中總阻力最低的船型，并通過數值計算和模型試驗結果的對比分析驗證了優化結果。 首先，在系統梳理靜水阻力和波浪增阻的數值計算方法及船型優化研究現狀的基礎上，提出了基于CAD與CFD相結合的SBD（Simulation Based Design）技術開發波浪中總阻力最低的船型集成優化系統的研究目標。 其次，論證了波浪中總阻力最低的船型集成優化系統中采用靜水阻力和波浪增阻的數值預報方法，并檢驗了阻力數值預報精度和反映船型變化的靈敏度，結果表明所采用計算方法雖存在一定的誤差，但都能正確的預報出船體阻力隨船型變化的趨勢。 第三，，為實現波浪增阻計算軟件在船型自動優化過程中的集成應用，開發了專門的增阻計算前處理接口程序，實現了常用標準幾何模型向增阻計算所需幾何模型的快速轉換。通過若干案列的幾何模型擬合度分析和增阻計算結果對比，檢驗了接口程序的精度和實用性，同時也證明了采用三次B樣條曲線擬合船體曲線的適用性。 第四，針對一艘30萬噸級油船，在Friendship軟件中構建了全參數化模型，開發了基于波浪中總阻力（含靜水阻力和波浪增阻）的集成優化系統。經試驗設計方法和遺傳算法二次優化得到了波浪中總阻力小的新改船型。并通過與原型及原改型的數值計算結果和模型試驗結果的對比，檢驗了船型集成優化系統的可行性。參數化船型自動集成優化系統突破了以往船型優化主要依賴設計者經驗的傳統模式，大大提高了優化效率。 最后，針對短波增阻精確預報這一波浪增阻數值計算難點，結合重疊網格技術，采用Level set方法捕捉自由面，應用SSTk湍流模型封閉并求解RANS方程和運動方程，獲得了船舶在靜水中和波浪中航行時所受到的阻力，初步探索了短波增阻的全粘流數值模擬方法。此外，通過實例對其精確度進行了驗證，發現計算結果與試驗結果相比尚存在一定的差距，有待進一步的研究。
[Abstract]:The traditional ship shape optimization is generally based on the lowest static water resistance, and the ship shape is measured by the speed in the still water. In fact, a ship is sailing in different sea conditions for most of its operation. The ship will be increased by the resistance caused by the wave, and the speediness of the ship with a good speed in the still water is not fast. In addition, reducing the resistance of the ship and reducing the power of the host are also the key to reduce fuel consumption and reduce carbon emissions. In this paper, a 300 thousand ton tanker is taken as the research object, with the minimum total resistance in the wave as the objective function, the integrated optimization system based on the static water resistance and wave resistance increase is realized. The ship shape is automatically optimized, and the ship hull with the lowest total resistance is obtained. The optimization results are verified through numerical analysis and comparative analysis of the model test results.
First, on the basis of the numerical calculation method of static water resistance and wave resistance increasing and the status of ship shape optimization, the goal of developing the ship type integrated optimization system based on the SBD (Simulation Based Design) technology based on CAD and CFD is proposed to develop the lowest total resistance of the wave in the wave.
Secondly, the numerical prediction method of static water resistance and wave increasing resistance in the ship type integrated optimization system with the lowest total resistance in the wave is demonstrated, and the numerical prediction precision of resistance and the sensitivity of the ship shape change are tested. The results show that although there is a certain error in the calculation method, the hull resistance can be correctly predicted with the ship. The trend of type change.
Third, in order to realize the integrated application of the wave increase resistance calculation software in the automatic optimization of the ship type, a special preprocessing interface program is developed, which realizes the rapid conversion of the common standard geometric model to the geometric model of the increase resistance calculation. The accuracy and practicability of the interface program are verified, and the applicability of the three B spline curve fitting hull curve is also proved.
Fourth, for a 300 thousand ton tanker, a fully parameterized model is built in Friendship software, and an integrated optimization system based on the total resistance in the wave (including static water resistance and wave resistance) is developed. The new modified ship model is obtained by the experimental design method and the genetic algorithm in two times. The feasibility of the ship type integrated optimization system is tested by the comparison between the numerical results and the model test results. The parametric ship type automatic integration optimization system breaks through the traditional model which mainly depends on the designer experience of the previous ship shape optimization, and greatly improves the optimization efficiency.
Finally, in order to predict the difficulty of the numerical calculation of the wave increasing resistance accurately, the Level set method is used to capture the free surface, and the SSTk turbulence model is used to seal and solve the RANS equation and motion equation, and the resistance of the ship to the navigation in the still water and the waves is obtained. In addition, the accuracy of the numerical simulation is verified by an example. It is found that there is still a gap between the calculated results and the experimental results, which needs further study.
【學位授予單位】：中國艦船研究院
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U662

【參考文獻】

相關期刊論文 前10條

1 王虎;鄒早建;;一種計算非線性興波阻力的基于NURBS的高階面元法(英文)[J];船舶力學;2009年03期

2 趙峰;李勝忠;楊磊;劉卉;;基于CFD的船型優化設計研究進展綜述[J];船舶力學;2010年07期

3 錢家昌;劉卉;;潛艇操縱性多目標優化及靈敏度分析[J];船舶力學;2011年07期

4 鄒勁,趙連恩;高速船波浪增阻的一種簡化計算及在船型設計中的應用[J];哈爾濱船舶工程學院學報;1993年04期

5 戴遺山，黃德波;船舶波浪增阻的近場和遠場公式[J];哈爾濱船舶工程學院學報;1994年01期

6 黃金鋒;萬松林;;基于設計特征的FRIENDSHIP船型參數化方法及實現[J];中國艦船研究;2012年02期

7 李子如;陳克強;;用面元法預報船舶的興波阻力及波型[J];武漢理工大學學報(交通科學與工程版);2006年06期

8 馮佰威;劉祖源;詹成勝;常海超;;船舶CAD/CFD一體化設計過程集成技術研究[J];武漢理工大學學報(交通科學與工程版);2010年04期

9 李建鵬;董國祥;蔣永旭;何惠明;;船舶在波浪中的增阻及艏部改型初步研究[J];上海船舶運輸科學研究所學報;2012年02期

10 陳京普;魏錦芳;朱德祥;;船舶在長峰和短峰不規則波中運動的三維時域數值模擬[J];水動力學研究與進展A輯;2011年05期

相關博士學位論文 前1條

1 張寶吉;船體線型優化設計方法及最小阻力船型研究[D];大連理工大學;2009年

本文編號：2154467