發布時間：2018-08-20 16:53

【摘要】：海洋鉆井平臺井架是目前國內各大海洋工程設備商剛剛開始涉足的領域。井架是整個鉆井系統的基礎結構,在鉆井作業中起到起重和掛載其他設備的作用。對于海洋鉆井平臺井架,國內的研究資料稀少,對此類平臺結構的受力特點了解不深,難以全面掌握其結構特性,發現潛在危險區域。這使得在實際工程中無法對此類井架結構的安全性提供有力的保障,同時也阻礙了我國海洋工程裝備的設計和開發。論文主要研究了海洋鉆井平臺井架的結構強度。此項研究可為我國自主設計海上鉆井平臺井架的結構設計提供相關技術和參考資料,有助于我國海洋工程設備的發展。本研究成果也可推廣到其他結構類型的井架結構設計。論文首先確定了海洋鉆井平臺井架結構強度的基本分析方法、制定了分析流程、總結了主要分析內容并給出了強度校核衡準;其次,全面討論了風載荷、大鉤載荷、鉆井扭矩、船體運動載荷等鉆井井架的外部載荷;最后,建立了典型平臺井架的有限元模型,研究和討論了有限元分析中的幾個關鍵技術,并對典型平臺井架結構進行了有限元直接計算,分析了井架的應力大小及分布,對井架整體結構強度和局部節點強度進行了校核。本論文主要研究結論為:(1)井架的支撐腿上靠近底部的桿件應力較高,日后如需要提升作業載荷的話應做適當加強。(2)受力最集中的天車橫梁最大強度利用因子為0.91,說明設計采用的構件尺寸滿足1000t大鉤載荷的作業能力,經濟合理。(3)總結了節點計算的關鍵點,以及計算流程。
[Abstract]:The Derrick of offshore drilling platform is a field that the major offshore engineering equipment manufacturers have just begun to set foot in at present. Derrick is the basic structure of the whole drilling system, which plays the role of lifting and mounting other equipment in drilling operation. For offshore drilling platform Derrick, the domestic research data are scarce, the mechanical characteristics of this kind of platform structure are not well understood, it is difficult to master its structural characteristics comprehensively and to find out the potential dangerous area. This makes it impossible to guarantee the safety of this kind of Derrick structure in practical engineering, and it also hinders the design and development of marine engineering equipment in China. This paper mainly studies the structural strength of offshore drilling platform Derrick. This study can provide relevant technology and reference materials for the structural design of offshore drilling platform Derrick in China, and is helpful to the development of marine engineering equipment in China. The research results can also be extended to other types of Derrick structure design. At first, the paper determines the basic analysis method of the structure strength of offshore drilling platform Derrick, formulates the analysis flow, summarizes the main contents of the analysis and gives the strength check, secondly, discusses comprehensively the wind load, the big hook load, the drilling torque, Finally, the finite element model of typical platform Derrick is established, several key techniques in finite element analysis are studied and discussed, and the finite element direct calculation of typical platform Derrick structure is carried out. The stress size and distribution of Derrick are analyzed, and the overall structural strength and local joint strength of Derrick are checked. The main conclusions of this paper are as follows: (1) the stress of the member near the bottom of the support leg of the Derrick is high. If it is necessary to raise the working load in the future, it should be strengthened appropriately. (2) the maximum strength utilization factor of the crane beam with the most concentrated force is 0.91. it shows that the dimensions of the components used in the design can meet the operational capacity of 1000t large hook load. (3) the key points of node calculation and the calculation flow are summarized.
【學位授予單位】：上海交通大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：U674.381

【參考文獻】

相關期刊論文 前1條

1 韓玉強;;鉆井井架動力測試與綜合性能評價[J];機械科學與技術;2012年10期

，

本文編號：2194335