發布時間：2019-01-25 08:59

【摘要】：目的研究不同Ni含量鐵基激光熔覆層的組織和性能。方法采用CO_2激光器制備了不同Ni含量的鐵基激光熔覆層,通過奧林巴斯光學顯微鏡、場發射掃描電鏡、X射線衍射儀及洛氏硬度計等設備,對激光熔覆層物相、微觀組織及力學性能進行表征。結果當Ni含量為10%~11%時,熔覆層物相主要由γ-Fe相組成,含有少量α-Fe相,洛氏硬度為35.1HRC,熔覆層殘余應力宏觀上表現為拉應力。當Ni含量為6%~7%時,熔覆層物相主要由α-Fe相組成,含有少量γ-Fe相,洛氏硬度為47.9HRC,熔覆層殘余應力宏觀上接近平衡狀態。當Ni含量為2%~3%時,熔覆層主要由α-Fe相組成,洛氏硬度為60.3HRC,熔覆層殘余應力宏觀上表現為壓應力。結論不同Ni含量熔覆層的物相主要由γ-Fe相和α-Fe相組成,隨著Ni含量的降低,熔覆層中γ-Fe相對應的衍射峰強度不斷減弱,而α-Fe相對應的衍射峰強度逐漸增強,熔覆層晶粒尺寸減小,表面洛氏硬度增加,殘余應力逐漸由拉應力轉變?yōu)閴簯?yīng)力,能夠有效抑制裂紋的生成,從而獲得高硬度不開裂熔覆層。
[Abstract]:Objective to study the microstructure and properties of iron based laser cladding coating with different Ni content. Methods the Fe-based laser cladding layer with different Ni content was prepared by CO_2 laser. The laser cladding phase was prepared by Olympus optical microscope, field emission scanning electron microscope, X-ray diffractometer and Rockwell hardness tester. Microstructure and mechanical properties were characterized. Results when the content of Ni was 10 ~ 11, the phase of the cladding was mainly composed of 緯-Fe phase, containing a small amount of 偽-Fe phase, and the Rockwell hardness was 35.1HRC. The residual stress of the cladding layer showed tensile stress macroscopically. When the content of Ni is 6 ~ 7, the phase of the cladding layer is mainly composed of 偽-Fe phase, containing a small amount of 緯-Fe phase, and the Rockwell hardness is 47.9 HRC. The residual stress of the cladding layer is close to equilibrium state macroscopically. When the Ni content is 2 ~ 3, the cladding layer is mainly composed of 偽-Fe phase, and the Rockwell hardness is 60.3 HRC. The residual stress of the cladding layer appears to be compressive stress macroscopically. Conclusion the phase of the cladding layer with different Ni content is mainly composed of 緯-Fe phase and 偽-Fe phase. With the decrease of Ni content, the diffraction peak intensity of 緯-Fe phase in the cladding layer decreases continuously, while the diffraction peak intensity corresponding to 偽-Fe phase increases gradually. The grain size of the cladding layer decreases, the surface hardness increases, and the residual stress gradually changes from tensile stress to compressive stress, which can effectively inhibit the formation of cracks and thus obtain the high hardness non-cracking cladding layer.
【作者單位】： 南華大學機械工程學院;
【基金】：國家自然科學基金項目(51474130) 湖南省市聯合基金重點項目(13JJ8013) 湖南省高校重點實驗室項目(湘財教指[2014]85號) 湖南省重點學科建設項目(湘教發[2011]76號) 湖南省高校科技創新團隊支持計劃(湘教通[2012]318號)~~
【分類號】：TG174.4

【相似文獻】

相關期刊論文 前10條

1 李勝;曾曉雁;胡乾午;;激光熔覆層力學性能評價方法的研究[J];熱加工工藝;2007年11期

2 王新林,石世宏,鄭啟光;激光熔覆層凝固特征與凝固組織控制研究[J];應用激光;2001年03期

3 吳健;影響激光熔覆層品質的主要因素分析[J];機械制造與自動化;2004年04期

4 王慧萍;;關于激光熔覆層開裂問題的探討[J];熱處理;2008年06期

5 李養良;羅紅梅;王利;陳清宇;;45鋼多道搭接激光熔覆層的組織與性能[J];熱加工工藝;2009年04期

6 程廣萍;李明喜;何宜柱;丁林;;激光熔覆層溫度場和應力場的數值模擬[J];熱處理;2009年04期

7 徐建林;楊波;龍大偉;陳紀東;于濤;張立輝;;鋁青銅表面激光熔覆層的潤滑摩擦性能[J];有色金屬;2010年02期

8 程衛華;王搖斌;;激光熔覆層的微觀檢測[J];蘭州石化職業技術學院學報;2011年02期

9 程衛華;王斌;陳明輝;;激光熔覆層的宏觀檢測[J];河南科技;2011年16期

10 楊寧;李立凱;;激光熔覆層的開裂行為及其防止[J];熱加工工藝;2011年24期

相關會議論文 前10條

1 黃德群;蘇寶Z，

本文編號：2414990